Xantrex C35, 35Amp Charge Controller 12/24V
The Xantrex C35-12/24V Charge Controller can be used for virtually any DC Charging Source. The C35 is field configurable for 12 and 24Vdc operation. It can be used as a charge, diversion, or load controller and comes with a standard multi-color charge status LED. Standard Features include a Silent Microprocessor Control. All C Series controllers have a powerful microprocessor at their core which increases system performance and maximizes battery life. They are fully solid state and operate silently. The C Series controllers all use Pulse Width Modulation (PWM) charging profiles which are designed to provide a full charge to your battery while, at the same time, minimize gassing which can shorten battery life. 3-Stage Battery Charging means the C Series controllers automatically initiate a 3-stage battery charging cycle. Bulk, Absorption, and Float modes are used to ensure that voltage and current settings accurately match the batteries' actual state of charge. This means fast-as-possible charging and extended battery life. An automatic equalization mode can be easily switched off when the controller is used with sealed batteries. C Series controllers are factory set for solar PV battery charging operation, but are field adjustable.
There are a number of field configurable, user adjustments for C Series controllers. C35 and C60's can only be set for 12/24Vdc operation. The C40 may be configured for 12, 24 or 48 volt systems. Bulk and Float voltage set points are programmable which allows us to use a wide variety of battery technologies including; flooded lead acid, gel, and absorbed glass mat (AGM). In addition, there are manually selectable settings for Nicad batteries.
When used as a load controller, the C Series will automatically turn a DC load on or off at predetermined battery voltage settings. Both LVD (low voltage disconnect) and LVR (low voltage reconnect) set points are user adjustable.
In DC Diversion Mode all power, which is not used to maintain a full charge on the batteries, is diverted to a load dump such as low voltage water or space heaters. Diversion mode is used to regulate micro-hydro and wind turbine systems which need a constant load.
A simple to read, multi-color LED indicates operating status and is standard on all C Series controllers.
Electrical Specifications: Voltage Configurations: 12 and 24Vdc. Max. PV Open Circuit Array Voltage: 55Vdc. Charging / Load Current: 35 amps DC. Max. Peak current: 85 amps Max. Voltage Drop through Controller: 0.30 volts. Typical Operating Consumption: 15 ma.Typical Idle Consumption: 3 ma. Recommended Breaker Size: 45 amps. Enclosure Type: Indoor, ventilated, powder coated steel with 3/4" and 1" knockouts. Unit Weight: 2.5 Lb"s (1.2 kg). Dimensions 8.0 H x 5.0 W x 2.5" D (20.3 x 17.8 x 6.4 cm) Mounting: Vertical wall mount - indoor only.
Warranty: Two years
Safety standards: C Series controllers are listed by UL to exacting UL 1741 and cUL CSA 22.2 107.1-95. C Series controllers are also CE compliant (European countries) and are designed to CTIK standards (Australia). Their current ratings are "real world" and do not have to be derated to comply with USA NEC 125% over-current requirements.
Display Panel: CM, CMR/50 or CMR/100-A, which is a back-lit meter that continuously displays: battery voltage, DC amperage, cumulative amp hours and amp hours since last reset. CM mounts on front of C Series, C35, C40 and C60, charge controllers. The remote meters CMR/50 and CMR/100 use simple telephone type plug-in connectors. 50 ft. (15 m) or 100 ft. (30 m) cable included.
Battery Temperature Sensor: BTS/15 or BTS/35 Monitors battery temperature and adjusts charging voltage for maximum performance. A 15 ft. (4.5 m) or 35 ft. (11 m) cable with standard telephone type connectors is included.
Call our toll free number 888-826-0939 if you have any questions about the C35 Solar Charge Controller by Xantrex